[ Previous | Next | Contents | Glossary | Home | Search ]
AIX Version 4.3 Commands Reference, Volume 5

telnetd Daemon

Purpose

Provides the server function for the TELNET protocol.

Syntax

/usr/sbin/telnetd -n ] [ -s ]

Description

Note: The telnetd daemon is normally started by the inetd daemon. It can also be controlled from the command line, using SRC commands.

The /usr/sbin/telnetd daemon is a server that supports the Defense Advanced Research Product Agency (DARPA) standard Telnet Protocol (TELNET). Changes to the telnetd daemon should be made using the System Management Interface Tool (SMIT).

Changes to the telnetd daemon can be made using the System Management Interface Tool (SMIT) or System Resource Controller (SRC), by editing the /etc/inetd.conf or /etc/services file. Entering telnetd at the command line is not recommended. The telnetd daemon is started by default when it is uncommented in the /etc/inetd.conf file.

The inetd daemon get its information from the /etc/inetd.conf file and the /etc/services file.

After changing the /etc/inetd.conf or /etc/services file, run the refresh -s inetd or kill -1 InetdPID command to inform the inetd daemon of the changes to its configuration file.

When a telnet session is started, the telnetd daemon sends TELNET options to the client (remote) host to indicate an ability to perform options.

Terminal Negotiation

The telnetd daemon requests the terminal type from the client host. On receipt, the telnetd daemon checks whether the indicated type is supported on the local system. If not, the daemon requests a terminal type again.

This terminal type negotiation continues until the remote client sends an acceptable terminal type or until the client sends the same type twice in a row, indicating that it has no other types available. When necessary, the telnetd daemon refers to the /etc/telnet.conf file to translate a client's terminal-type strings into terminfo file entries.

Note: Since the telnetd daemon allows the sending and receiving of 8-bit ASCII, NLS is supported.

If the remote client sends the TELNET SAK command, the telnetd daemon passes the local SAK characters through the PTY to invoke the trusted shell.

The telnetd daemon supports the following TELNET options:

The telnetd daemon also recognizes the following options for the remote client:

The telnetd daemon should be controlled using the System Management Interface Tool (SMIT) or by changing the /etc/inetd.conf file. Entering telnetd at the command line is not recommended.

Authenication Negotiation

If the system has Kerberos 5 authentication configured, telnetd will accept authentication option negotiation. If both agree on Kerberos 5 authentication, the client will pass over the DCE principal and telnetd will use the kvalid_user routine to determine if the DCE principal should have access to the account. If it passes, no password will be requested.

Manipulating the telnetd Daemon with the System Resource Controller

The telnetd daemon is a subserver of the inetd daemon, which is a subsystem of the System Resource Controller (SRC). The telnetd daemon is a member of the tcpip SRC subsystem group. This daemon is enabled by default in the /etc/inetd.conf file and can be manipulated by the following SRC commands:

startsrc Starts a subsystem, group of subsystems, or a subserver.
stopsrc Stops a subsystem, group of subsystems, or a subserver.
lssrc Gets the status or a subsystem, group or subsystems, or a subserver.

Flags

-n Disables transport-level keep-alive messages. Messages are enabled by default.
-s Turns on socket-level debugging.

Examples

Note: The arguments for the telnetd daemon can be specified by using SMIT or by editing the /etc/inetd.conf file.
  1. To start the telnetd daemon, enter the following:
    startsrc -t telnet
    This command starts the telnetd subserver.
  2. To stop the telnetd daemon normally, enter the following:
    stopsrc -t telnet
    This command allows all pending connections to start and existing connections to complete but prevents new connections from starting.
  3. To force stop the telnetd daemon and all telnetd connections, enter the following:
    stopsrc -t -f telnet
    This command terminates all pending connections and existing connections immediately.
  4. To display a short status report about the telnetd daemon, enter the following:
    lssrc -t telnet
    This command returns the daemon's name, process ID, and state (active or inactive).

File

terminfo Describes terminal by capability.

Related Information

The ftp command, kill command, lssrc command, rcp command, refresh command, rlogin command, rsh command, startsrc command, stopsrc command, telnet command.

The kill command, lssrc command, refresh command, startsrc command, stopsrc command, telnet command.

The /etc/inetd.conf file format, /etc/telnet.conf file format.

The pty special file.

The kvalid_user subroutine.

Telnet Protocol (TELNET) in AIX Version 4.3 System Management Guide: Communications and Networks.

TCP/IP Daemons in AIX Version 4.3 System Management Guide: Communications and Networks.

Secure Rcmds in AIX Version 4.3 System User's Guide: Communications and Networks.


[ Previous | Next | Contents | Glossary | Home | Search ]