This category of identifiers contains the following error labels:
X25 ADAPT X25 ALERT5 X25 ALERT7
X25 ALERT8 X25 ALERT9 X25 ALERT10
X25 ALERT11 X25 ALERT12 X25 ALERT13
X25 ALERT14 X25 ALERT15 X25 ALERT16
X25 ALERT17 X25 ALERT18 X25 ALERT19
X25 ALERT21 X25 ALERT22 X25 ALERT23
X25 ALERT24 X25 ALERT25 X25 ALERT26
X25 ALERT27 X25 ALERT28 X25 ALERT29
X25 ALERT30 X25 ALERT31 X25 ALERT32
X25 ALERT33 X25 ALERT34 X25 ALERT35
X25 ALERT36 X25 ALERT37 X25 ALERT38
X25 ALERT39 X25 CONFIG X25 IPL
X25 UCODE
Go back to the categories of Error Identifiers.
Error Description: ADAPTER ERROR
This error is logged by the X.25 device driver if the adapter card could not be found on the bus.
Sense Data | The sense data consists of failure data which is analyzed by the Diagnostic Programs. |
Error Description: X-5, MODEM FAILURE: DCD, DSR, CABLE
This error is logged by the X.25 device driver if the physical layer cannot be established to the modem. The signal lines DCD and DSR are not active.
Refer to Detail Data under X25 ADAPT.
Error Description: X-7, MODEM FAILURE: ACU NOT RESPONDING
This error is logged by the X.25 device driver if the attached auto-call unit failed to establish a call.
Refer to Detail Data under X25 ADAPT.
Error Description: X-8, X.21 NOT CONNECTED
This error is logged by the X.25 device driver when it fails to connect to an X.21 network.
Refer to Detail Data under X25 ADAPT.
Error Description: X-9, FRAME TYPE W RECEIVED
This error is logged by the X.25 device driver if a W type FRMR frame is received.
Refer to Detail Data under X25 ADAPT.
Error Description: X-10, FRAME TYPE X RECEIVED
This error is logged by the X.25 device driver if an X type FRMR frame is received.
Refer to Detail Data under X25 ADAPT.
Error Description: X-11, FRAME TYPE Y RECEIVED
This error is logged by the X.25 device driver when a Y type FRMR frame is received.
Refer to Detail Data under X25 ADAPT.
Error Description: X-12, FRAME TYPE Z RECEIVED
This error is logged by the X.25 device driver when a Z type FRMR frame is received.
Refer to Detail Data under X25 ADAPT.
Error Description: X-13, FRAME TYPE W TRANSMITTED
This error is logged by the X.25 device driver when a W type FRMR frame is transmitted.
Refer to Detail Data under X25 ADAPT.
Error Description: X-14, FRAME TYPE X TRANSMITTED
This error is logged by the X.25 device driver when an X type FRMR frame is transmitted.
Refer to Detail Data under X25 ADAPT.
Error Description: X-15, FRAME TYPE Y TRANSMITTED
This error is logged by the X.25 device driver when a Y type FRMR frame is transmitted.
Refer to Detail Data under X25 ADAPT.
Error Description: X-16, FRAME TYPE Z TRANSMITTED
This error is logged by the X.25 device driver when a Z type FRMR frame is transmitted.
Refer to Detail Data under X25 ADAPT.
Error Description: X-17, FRAME RETRY N2 REACHED
This error is logged by the X.25 device driver when the frame level retry count (N2) is reached.
Refer to Detail Data under X25 ADAPT.
Error Description: X-18, UNEXPECTED DISC RECEIVED
This error is logged by the X.25 device driver if a disconnect frame is received unexpectedly.
Refer to Detail Data under X25 ADAPT.
Error Description: X-19, DM RXD DURING LINK ACTIVATION
This error is logged by the X.25 device driver when a DM frame was received after sending a SABM.
Refer to Detail Data under X25 ADAPT.
Error Description: X-21, CLEAR INDICATION RECEIVED
This error is logged by the X.25 device driver if a clear indication packet with DCE-originated cause and diagnostics is received.
Refer to Detail Data under X25 ADAPT.
Error Description: X-22, RESTART INDICATION RECEIVED
This error is logged by the X.25 device driver after a restart indication packet containing a DCE-originated cause and diagnostics was received by the DCE.
Refer to Detail Data under X25 ADAPT.
Error Description: X-23, RESET REQUEST BY X.25 ADAPTER
This error is logged by the X.25 device driver if a reset request packet is sent automatically by the adapter.
Refer to Detail Data under X25 ADAPT.
Error Description: X-24, CLEAR REQUEST BY X.25 ADAPTER
This error is logged by the X.25 device driver when the adapter code sent out a clear request with DCE-originated cause and diagnostics. The clear was not one requested by a higher layer.
Refer to Detail Data under X25 ADAPT.
Error Description: X-25, RESTART REQUEST BY X.25 ADAPTER
This error is logged by the X.25 device driver when a restart request containing DCE-originated cause and diagnostics is transmitted.
Refer to Detail Data under X25 ADAPT.
Error Description: X-26, TIMEOUT ON RESTART REQUEST, T20
This error is logged by the X.25 device driver if timer T20 expires before receipt of a restart confirmation packet.
Refer to Detail Data under X25 ADAPT.
Error Description: X-27, TIMEOUT ON RESET REQUEST, T22
This error is logged by the X.25 device driver if timer T22 expires before receipt of a reset confirmation packet.
Refer to Detail Data under X25 ADAPT.
Error Description: X-28, TIMEOUT ON CALL REQUEST, T21
This error is logged by the X.25 device driver if timer T21 expired before receipt of either a call connected or clear indication packet.
Refer to Detail Data under X25 ADAPT.
Error Description: X-29, TIMEOUT ON CLEAR REQUEST, T23
This error is logged by the X.25 device driver if timer T23 expires before receipt of a clear confirmation packet.
Refer to Detail Data under X25 ADAPT.
Error Description: X-30, DIAGNOSTIC PACKET RECEIVED
This error is logged by the X.25 device driver if a diagnostic packet is received.
Refer to Detail Data under X25 ADAPT.
Error Description: X-31, RESET INDICATION PACKET RECEIVED
This error is logged by the X.25 device driver when a reset indication packet with DCE-originated cause and diagnostics is received.
Refer to Detail Data under X25 ADAPT.
Error Description: X-32, (DCE) CLEAR INDICATION BY X.25 ADAPTER
This error is logged by the X.25 device driver when a clear indication containing DCE-generated cause and diagnostics is received.
Refer to Detail Data under X25 ADAPT.
Error Description: X-33, (DCE) RESET INDICATION BY X.25 ADAPTER
This error is logged by the X.25 device driver if a reset indication packet containing a DCE-originated cause and diagnostics is received.
Refer to Detail Data under X25 ADAPT.
Error Description: X-34, (DCE) RESTART INDICATION BY X.25 ADAPTER
This error is logged by the X.25 device driver after a restart indication packet containing a DCE-originated cause and diagnostics is received.
Refer to Detail Data under X25 ADAPT.
Error Description: X-35, (DCE) RESTART REQUEST RECEIVED
This error is logged by the X.25 device driver when a restart request indication packet with DCE-originated cause and diagnostic codes is received.
Refer to Detail Data under X25 ADAPT.
Error Description: X-36, (DCE) TIMEOUT ON RESTART INDICATION, T10
This error is logged by the X.25 device driver when timer T10 expired at the DCE before receipt of a restart confirmation packet.
Refer to Detail Data under X25 ADAPT.
Error Description: X-37, (DCE) TIMEOUT ON RESET INDICATION, T12
This error is logged by the X.25 device driver if timer T12 expired before receipt of a reset confirmation packet.
Refer to Detail Data under X25 ADAPT.
Error Description: X-38, (DCE) TIMEOUT ON CALL INDICATION, T11
This error is logged by the X.25 device driver if timer T11 expired before receipt of a call accept or clear request packet.
Refer to Detail Data under X25 ADAPT.
Error Description: X-39, (DCE) TIMEOUT ON CLEAR INDICATION, T13
This error is logged by the X.25 device driver if timer T13 expired before receipt of a clear confirmation packet.
Refer to Detail Data under X25 ADAPT.
Error Description: X.25 CONFIGURATION ERROR
This error is logged by the X.25 device driver when the adapter fails its internal configuration.
Refer to Detail Data under X25 ADAPT.
Error Description: ADAPTER ERROR
This error is logged by the X.25 device driver if an adapter timed out during the reboot sequence. This is an installation-related problem and may indicate that the communication equipment was not installed correctly or that the hardware and microcode are incompatible.
Refer to Detail Data under X25 ADAPT.
Error Description: X.25 MICROCODE ERROR
This error is logged by the X.25 device driver if the adapter microcode terminates abnormally.
Refer to Detail Data under X25 ADAPT.