This category of identifiers contains the following error labels:
TOK ADAP CHK TOK ADAP ERR TOK AUTO RMV
TOK BAD ASW TOK BEACON1 TOK BEACON2
TOK BEACON3 TOK CONGEST TOK DOWNLOAD
TOK DUP ADDR TOK ERR5 TOK ERR10
TOK ERR15 TOK ESERR TOK MC ERR
TOK NOMBUFS TOK PIOERR TOK RCVRY ENTER
TOK RCVRY EXIT TOK RCVRY EXIT TOK RCVRY TERM
TOK RMV ADAP1 TOK RMV ADAP2 TOK TX ERR
TOK WIRE FAULT TOK WRAP TST
Go back to the categories of Error Identifiers.
Error Description: ADAPTER ERROR
This error indicates that a Token-Ring adapter check has occurred.
Sense Data | The sense data consists of failure data which is analyzed by the Diagnostic Programs. |
Additional Subvectors | |
Additional alert subvectors. |
Error Description: POTENTIAL DATA LOSS CONDITION
This error is logged when there may be downlevel Token-Ring equipment installed. A potential data loss condition is possible.
Refer to the Detail Data under TOK ADAP CHK.
Error Description: AUTO REMOVAL
This error indicates that the adapter was a member of the beacon fault domain and removed itself to perform a self-test, which was unsuccessful.
Refer to the Detail Data under TOK ADAP CHK.
Error Description: MICROCODE PROGRAM ERROR
This error indicates an incompatible microcode and adapter.
Refer to the Detail Data under TOK ADAP CHK.
Error Description: OPEN FAILURE
This error indicates that the adapter detected a beaconing condition on the ring during the insertion process.
Refer to the Detail Data under TOK ADAP CHK.
Error Description: TOKEN-RING INOPERATIVE
This error indicates that the ring was in a beaconing condition for longer than the time allowed by the hard-error detection timer.
Refer to the Detail Data under TOK ADAP CHK.
Error Description: TOKEN-RING TEMPORARY ERROR
This error indicates that ring was in a beaconing condition for less than 52 seconds and was then recovered.
Refer to the Detail Data under TOK ADAP CHK.
Error Description: COMMUNICATIONS OVERRUN
This error indicates that the ring error monitor (REM) detected an adapter on the ring that is experiencing excessive congestion and is discarding a significant number of frames.
Refer to the Detail Data under TOK ADAP CHK.
Error Description: MICROCODE PROGRAM ABNORMALLY TERMINATED
This error indicates that the microcode download failed.
Error Description: OPEN FAILURE
This error indicates that the adapter detected the presence of a station with its individual address on the ring during the insertion process.
Refer to the Detail Data under TOK ADAP CHK.
Error Description: OPEN FAILURE
This error indicates that an unknown adapter hardware error occurred during the insertion process.
Refer to the Detail Data under TOK ADAP CHK.
Error Description: AUTO REMOVAL
Refer to the Detail Data under TOK ADAP CHK.
Error Description: ADAPTER ERROR
This error indicates that the Token-Ring device handler caught an unknown system error.
Refer to the Detail Data under TOK ADAP CHK.
Error Description: EXCESSIVE TOKEN-RING ERRORS
This error indicates that the ring error monitor (REM) detected excessive soft errors for the ring.
Refer to the Detail Data under TOK ADAP CHK.
Error Description: ADAPTER ERROR
This error indicates that the Token-Ring device handler has detected a Micro Channel error.
Refer to the Detail Data under TOK ADAP CHK.
Error Description: RESOURCE UNAVAILABLE
This error indicates that a Token-Ring device handler request for an mbuf structure was denied.
Refer to the Detail Data under TOK ADAP CHK.
Error Description: ADAPTER ERROR
This error indicates that the Token-Ring device handler has detected a programmable input/output error.
Refer to the Detail Data under TOK ADAP CHK.
Error Description: ADAPTER ERROR
This error indicates that the Token-Ring device handler has entered Network Recovery Mode.
This error indicates that the Token-Ring device handler has exited Network Recovery mode successfully.
Refer to the Detail Data under TOK ADAP CHK.
Error Description: ADAPTER ERROR
This error indicates that the Token-Ring device handler has terminated Network Recovery mode.
Refer to the Detail Data under TOK ADAP CHK.
Error Description: OPEN FAILURE
This error indicates that the adapter received a Remove Ring Station MAC frame during the insertion process.
Refer to the Detail Data under TOK ADAP CHK.
Error Description: REMOVE ADAPTER COMMAND RECEIVED
This error indicates that the adapter received a Remove Adapter command from a LAN manager and left the LAN.
Refer to the Detail Data under TOK ADAP CHK.
Error Description: ADAPTER ERROR
This error indicates that the Token-Ring device handler has detected a transmission error.
Refer to the Detail Data under TOK ADAP CHK.
This error indicates a wire-fault condition on the ring.
Refer to the Detail Data under TOK ADAP CHK.
Error Description: OPEN FAILURE
This error indicates that the adapter detected a problem on its lobe during the wrap-test portion of the insertion process.
Refer to the Detail Data under TOK ADAP CHK.