[ Previous | Next | Contents | Glossary | Home | Search ]
AIX Version 4.3 Messages Guide and Reference

List of Three-Digit Display Values: 500-599, 5c0-5c6

Display Value 500

Explanation Progress indicator. Querying standard I/O slot.
System Action If an irrecoverable error occurs, the system halts.
User Action If the system halts, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference.

If there is a hardware failure, report it to your hardware service organization. If not, report the failure to your software service organization, and then stop. You have completed these procedures.

Display Value 501

Explanation Progress indicator. Querying card in slot 1.
System Action If an irrecoverable error occurs, the system halts.
User Action If the system halts, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference.

If there is a hardware failure, report it to your hardware service organization. If not, report the failure to your software service organization, and then stop. You have completed these procedures.

Display Value 502

Explanation Progress indicator. Querying card in slot 2.
System Action If an irrecoverable error occurs, the system halts.
User Action If the system halts, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference.

If there is a hardware failure, report it to your hardware service organization. If not, report the failure to your software service organization, and then stop. You have completed these procedures.

Display Value 503

Explanation Progress indicator. Querying card in slot 3.
System Action If an irrecoverable error occurs, the system halts.
User Action If the system halts, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference.

If there is a hardware failure, report it to your hardware service organization. If not, report the failure to your software service organization, and then stop. You have completed these procedures.

Display Value 504

Explanation Progress indicator. Querying card in slot 4.
System Action If an irrecoverable error occurs, the system halts.
User Action If the system halts, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference.

If there is a hardware failure, report it to your hardware service organization. If not, report the failure to your software service organization, and then stop. You have completed these procedures.

Display Value 505

Explanation Progress indicator. Querying card in slot 5.
System Action If an irrecoverable error occurs, the system halts.
User Action If the system halts, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference.

If there is a hardware failure, report it to your hardware service organization. If not, report the failure to your software service organization, and then stop. You have completed these procedures.

Display Value 506

Explanation Progress indicator. Querying card in slot 6.
System Action If an irrecoverable error occurs, the system halts.
User Action If the system halts, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference.

If there is a hardware failure, report it to your hardware service organization. If not, report the failure to your software service organization, and then stop. You have completed these procedures.

Display Value 507

Explanation Progress indicator. Querying card in slot 7.
System Action If an irrecoverable error occurs, the system halts.
User Action If the system halts, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference.

If there is a hardware failure, report it to your hardware service organization. If not, report the failure to your software service organization, and then stop. You have completed these procedures.

Display Value 508

Explanation Progress indicator. Querying card in slot 8.
System Action If an irrecoverable error occurs, the system halts.
User Action If the system halts, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference.

If there is a hardware failure, report it to your hardware service organization. If not, report the failure to your software service organization, and then stop. You have completed these procedures.

Display Value 510

Explanation Progress indicator. Starting device configuration.
System Action Configuration manager started. If an irrecoverable error occurs, the system halts.
User Action If the system halts, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference.

If there is a hardware failure, report it to your hardware service organization. If not, report the failure to your software service organization, and then stop. You have completed these procedures.

Display Value 511

Explanation Progress indicator. Device configuration completed.
System Action Configuration manager ended. If an irrecoverable error occurs, the system halts.
User Action If the system halts, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference.

If there is a hardware failure, report it to your hardware service organization. If not, report the failure to your software service organization, and then stop. You have completed these procedures.

Display Value 512

Explanation Progress indicator. Restoring device configuration files from media.
System Action Reading device configuration files from media. If an irrecoverable error occurs, the system halts.
User Action If the system halts, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference.

If there is a hardware failure, report it to your hardware service organization. If not, report the failure to your software service organization, and then stop. You have completed these procedures.

Display Value 513

Explanation Progress indicator. Restoring BOS installation files from media.
System Action Reading device configuration files from media during BOS installation. If an irrecoverable error occurs, the system halts.
User Action If the system halts, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference.

If there is a hardware failure, report it to your hardware service organization. If not, report the failure to your software service organization, and then stop. You have completed these procedures.

Display Value 516

Explanation Progress indicator. Contacting server during network boot.
System Action Contacting server during network boot. If an irrecoverable error occurs, the system halts.
User Action If the system halts, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference.

If there is a hardware failure, report it to your hardware service organization. If not, report the failure to your software service organization, and then stop. You have completed these procedures.

Display Value 517

Explanation Progress indicator. The / (root) and /usr file systems are being mounted.
System Action The system is attempting to mount the / (root) and /usr file systems. These file systems are of type bootfs.
User Action If the mount does not successfully complete during a network boot, the system changes the three-digit display value to 518. If the system halts with a 517 in the three-digit display, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference.

If there is a hardware failure, report it to your hardware service organization. If not, report the failure to your software service organization, and then stop. You have completed these procedures.

Display Value 518

Explanation Remote mount of the / (root) and /usr file systems during network boot did not complete successfully.
System Action The system halts.
User Action You will need to log on to the server or to another client with superclient privileges to go to the following activities:
  • Verify that the type field for the / (root) and /usr file systems is correct in the client's /etc/filesystems file. To do this, run the following command: 
    pg /export/root/ClientHostName/etc/filesystems

    Make sure that the / (root) and /usr stanzas contain a line that reads type=bootfs. If the type field is incorrect, use a text editor to correct it.

Display Value 520

Explanation Progress indicator. Bos configuration is running.
System Action If an irrecoverable error occurs, the system halts.
User Action If the system halts, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference.

If there is a hardware failure, report it to your hardware service organization. If not, report the failure to your software service organization, and then stop. You have completed these procedures.

  • Verify that the client's file systems are exported by that server. To do this, run the following command: 
    /usr/bin/showmount -e ServerHostName

    If the client's / (root) or /usr file systems are not in the list, use a text editor to add them to the /etc/exports file. After you have saved the changes, run the following command to update the client's root file system: 

    /usr/sbin/exportfs
  • Run the following command to verify that the nfsd daemon is running on the server: 
    ps -e | grep nfsd

    If the system does not return any data, the daemon is not running and must be started using the following command: 

    /etc/rc.nfs

If you are unable to correct the problem, contact your software service organization for assistance.

Display Value 521

Explanation The /etc/inittab file has been incorrectly modified or is damaged.
System Action The configuration manager was started from the /etc/inittab file with invalid options. The system halts.
User Action The problem can usually be solved by entering Maintenance mode and either correcting the damaged file or replacing it with a copy from the installation media or another system. Refer to "Accessing a System That Will Not Boot" for information on loading the Maintenance mode onto your system. If you are not familiar with this mode or are unable to correct the problem, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 522

Explanation The /etc/inittab file has been incorrectly modified or is damaged.
System Action The configuration manager was started from the /etc/inittab file with conflicting options. The system halts.
User Action The problem can usually be solved by entering Maintenance mode and either correcting the damaged file or replacing it with a copy from the installation media or another system. Refer to "Accessing a System That Will Not Boot" for information on loading the Maintenance mode onto your system. If you are not familiar with this mode or are unable to correct the problem, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 523

Explanation The /etc/objrepos file is missing or inaccessible.
System Action The configuration manager is unable to access the ODM database. The system halts.
User Action Go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference to determine if there is a problem with the device where the files reside.

If these procedures do not find a problem with a device, the problem can usually be corrected by entering Maintenance mode and either correcting the damaged files or replacing them with a copy from the installation media or another system.

Refer to "Accessing a System That Will Not Boot" for information on loading the Maintenance mode onto your system. If you are not familiar with this mode or are unable to correct the problem, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 524

Explanation The /etc/objrepos/Config_Rules file is missing or inaccessible.
System Action The configuration manager is unable to access the Config_Rules object in the ODM database. This error halts the system.
User Action Go to " Hardware Diagnostics" in in AIX Problem Solving Guide and Reference to determine if there is a problem with the device where the file resides.

If these procedures do not find a problem with a device, the problem can usually be corrected by entering Maintenance mode and either correcting the damaged file or replacing it with a copy from the installation media or another system.

Refer to "Accessing a System That Will Not Boot" for information on loading the Maintenance mode onto your system. If you are not familiar with this mode or are unable to correct the problem, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 525

Explanation The /etc/objrepos/CuDv file is missing or inaccessible.
System Action The configuration manager is unable to access the Customized Device Driver object in the ODM database. This error halts the system.
User Action Go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference to determine if there is a problem with the device where the file resides.

If these procedures do not find a problem with a device, the problem can usually be corrected by entering Maintenance mode and either correcting the damaged file or replacing it with a copy from the installation media or another system.

Refer to "Accessing a System That Will Not Boot" for information on loading the Maintenance mode onto your system. If you are not familiar with this mode or are unable to correct the problem, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 526

Explanation The /etc/objrepos/CuDvDr file is missing or inaccessible.
System Action The configuration manager is unable to access the Customized Device Driver object in the ODM database. This error halts the system.
User Action Go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference to determine if there is a problem with the device where the file resides.

If these procedures do not find a problem with a device, the problem can usually be corrected by entering Maintenance mode and either correcting the damaged file or replacing it with a copy from the installation media or another system.

Refer to "Accessing a System That Will Not Boot" for information on loading the Maintenance mode onto your system. If you are not familiar with this mode or are unable to correct the problem, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 527

Explanation You cannot run Phase 1 at this point. The /sbin/rc.boot file has probably been incorrectly modified or is damaged.
System Action The configuration manager was started with the Phase 1 flag. This error halts the system.
User Action Go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference to determine if there is a problem with the device where the file resides.

If these procedures do not find a problem with a device, the problem can usually be corrected by entering Maintenance mode and either correcting the damaged file or replacing it with a copy from the installation media or another system.

Refer to "Accessing a System That Will Not Boot" for information on loading the Maintenance mode onto your system. If you are not familiar with this mode or are unable to correct the problem, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 528

Explanation The /etc/objrepos/Config_Rules file has been incorrectly modified or is damaged, or a program specified in the file is missing.
System Action The configuration manager cannot find the sequence rule specified in the Config_Rules object in the ODM database, or no program was specified. This error halts the system.
User Action Go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference to determine if there is a problem with the device where the file resides.

If these procedures do not find a problem with a device, the problem can usually be corrected by entering Maintenance mode and either correcting the damaged file or replacing it with a copy from the installation media or another system.

Refer to "Accessing a System That Will Not Boot" for information on loading the Maintenance mode onto your system. If you are not familiar with this mode or are unable to correct the problem, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 529

Explanation There is a problem with the device containing the ODM database or the root file system is full.
System Action The configuration manager is unable to update the ODM database. This error halts the system.
User Action Go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference . If the diagnostic programs do not find a problem, enter Maintenance mode. Determine if your file system is full by issuing the following command: 
df /

If your root file system is full, you will need to make space available on your system. You can accomplish this by removing the /smit.log and /smit.script files if they have become large. Before removing these files, you may want to copy them to diskette or tape.

  • To copy the SMIT files to diskette, use the following command: 
    ls /smit.log /smit.script | backup -iv
  • To copy the SMIT files to streaming tape, use the following command: 
    ls /smit.log /smit.script | backup -ivf /dev/rmt0
  • To copy the SMIT files to 9-track tape, use the following command: 
    ls /smit.log /smit.script | backup -ivf /dev/rmt0

After you have copied the files, remove them by using the following command: 

rm /smit.log /smit.script

Refer to "Accessing a System That Will Not Boot" for information on loading the Maintenance mode onto your system. If you are not familiar with this mode or are unable to correct the problem, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 530

Explanation The savebase command was unable to save information about the base customized devices onto the boot device during Phase 1 of system boot.
System Action The savebase command returned an error. This error halts the system.
User Action Go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference . If these procedures find a problem, report the problem to your hardware service organization, and then stop. You have completed these procedures.

If you are unable to correct this problem, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 531

Explanation The /usr/lib/objrepos/PdAt file is missing or inaccessible.
System Action The configuration manager is unable to access the Predefined Attribute object in the ODM database. This error halts the system.
User Action If the system halts, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference to determine if there is a problem with the device where the files reside.

If these procedures do not find a problem with a device, the problem can usually be corrected by entering Maintenance mode and either correcting the damaged file or replacing it with a copy from the installation media or another system.

Refer to "Accessing a System That Will Not Boot" for information on loading the Maintenance mode onto your system. If you are not familiar with this mode or are unable to correct the problem, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 532

Explanation There is not enough memory for the configuration manager to continue.
System Action The configuration manager ran out of memory. This error halts the system.
User Action If the system halts, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference . If these procedures find a problem, report the problem to your hardware service organization. Otherwise, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 533

Explanation The /usr/lib/objrepos/PdDv file has been incorrectly modified or is damaged, or a program specified in the file is missing.
System Action The configuration manager could not find a configure method for a device.
User Action If the system halts, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference to determine if there is a problem with the device where the file resides.

If these procedures do not find a problem with a device, the problem can usually be corrected by entering Maintenance mode and either correcting the damaged file or replacing it with a copy from the installation media or another system.

Refer to "Accessing a System That Will Not Boot" for information on loading the Maintenance mode onto your system. If you are not familiar with this mode or are unable to correct the problem, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 534

Explanation The configuration manager is unable to acquire a database lock.
System Action The configuration manager is unable to lock the ODM database. This error halts the system.
User Action Go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference . If these procedures find a problem, report the problem to your hardware service organization. Otherwise, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 535

Explanation A HIPPI diagnostics interface driver being is configured.
System Action The configuration method for a HIPPI diagnostics interface driver is being run. If an irrecoverable error occurs, the system halts.
User Action Go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference . If these procedures find a problem, report the problem to your hardware service organization. Otherwise, report the problem to your software service organization.

Display Value 536

Explanation The /etc/objrepos/Config_Rules file has been incorrectly modified or is damaged.
System Action The configuration manager encountered more than one sequence rule specified in the same phase. This error halts the system.
User Action Go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference to determine if there is a problem with the device where the files reside.

If these procedures do not find a problem with a device, the problem can usually be corrected by entering Maintenance mode and either correcting the damaged file or replacing it with a copy from the installation media or another system.

Refer to "Accessing a System That Will Not Boot" for information on loading the Maintenance mode onto your system. If you are not familiar with this mode or are unable to correct the problem, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 537

Explanation The /etc/objrepos/Config_Rules file has been incorrectly modified or is damaged, or a program specified in the file is missing.
System Action The configuration manager encountered an error when starting the program in the sequence rule. This error halts the system.
User Action Go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference to determine if there is a problem with the device where the files reside.

If these procedures do not find a problem with a device, the problem can usually be corrected by entering Maintenance mode and either correcting the damaged file or replacing it with a copy from the installation media or another system.

Refer to "Accessing a System That Will Not Boot" for information on loading the Maintenance mode onto your system. If you are not familiar with this mode or are unable to correct the problem, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 538

Explanation Progress indicator. The configuration manager is passing control to a configuration method.
System Action If a transfer of control is not successful, the system halts.
User Action If the system halts with this value displayed, report the problem to your software service organization.

Display Value 539

Explanation Progress indicator. The configuration method has ended and control has returned to the configuration manager.
System Action If a transfer of control is not successful, the system halts.
User Action If the system halts with this value displayed, report the problem to your software service organization.

Display Value 540

Explanation Progress indicator. Configuring child of IEEE-1284 parallel port.
System Action Configuration method is executing.
User Action If the system halts with this value displayed, report the problem to your software service organization.

Display Value 544

Explanation Progress indicator. An ECP peripheral configure method is executing.

Display Value 545

Explanation Progress indicator. A parallel port ECP device driver is being configured.

Display Value 546

Explanation IPL cannot continue due to error in customized database.

Display Value 547

Explanation Rebooting after error recovery. (LED 546 precedes this LED).

Display Value 548

Explanation Restbase failure.

Display Value 549

Explanation Console could not be configured for the "Copy a System Dump"menu.

Display Value 550

Explanation Progress indicator. ATM LAN emulation device driver is being configured.

Display Value 551

Explanation Progress indicator. A varyon operation of the root volume group is in progress.
System Action The system is varying on the root volume group. If this process is not successful, the system halts.
User Action See "Booting Problems" for recovery procedures. If those procedures fail to correct the problem, record SRN 101-201 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 552

Explanation The ipl_varyon command failed with a return code not equal to 4, 7, 8, or 9 (ODM or malloc failure).
System Action The system is unable to varyon the root volume group. This error halts the system.
User Action See "Booting Problems" for recovery procedures. If those procedures fail to correct the problem, record SRN 101-201 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 553

Explanation The /etc/inittab file has been incorrectly modified or is damaged.
System Action Phase 1 boot is completed and the init command started.
User Action See "Booting Problems" for recovery procedures. If those procedures fail to correct the problem, record SRN 101-201 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 554

Explanation The IPL device could not be opened or a read failed (hardware not configured or missing).
System Action The system halts.
User Action Go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference to determine if there is a problem with the device where the files reside.

If these procedures do not find a problem with a device, the problem is usually due to bad information on the boot logical volume, or the log logical volume (/dev/hd8) has been damaged.

To correct the problem with the boot logical volume, enter Maintenance mode (refer to "Accessing a System That Will Not Boot" for information on loading the Maintenance mode onto your system), then run the savebase command. When the savebase command completes, issue the sync; sync command. After this command completes, restart the system in Normal mode.

If this does not correct the problem, reenter Maintenance mode and enter the /usr/sbin/logform /dev/hd8 command. When this command completes, restart the system in Normal mode.

If you are not familiar with this mode or are unable to correct the problem, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 555

Explanation Using the fsck -fp /dev/hd4 command on the root file system failed with a nonzero return code.
System Action The system halts.
User Action Go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference to determine if there is a problem with the device where the files reside.

If these procedures do not find a problem with a device, the problem is usually due to bad information on the boot logical volume, or the log logical volume (/dev/hd8) has been damaged.

To correct the problem with the boot logical volume, enter Maintenance mode (refer to "Accessing a System That Will Not Boot" for information on loading the Maintenance mode onto your system), then run the savebase command. When the savebase command completes, issue the sync; sync command. After this command completes, restart the system in Normal mode.

If this does not correct the problem, reenter Maintenance mode and enter the /usr/sbin/logform /dev/hd8 command. When this command completes, restart the system in Normal mode.

If you are not familiar with this mode or are unable to correct the problem, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 556

Explanation LVM subroutine error from ipl_varyon.
System Action The system halts.
User Action Go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference to determine if there is a problem with the device where the files reside.

If these procedures do not find a problem with a device, the problem is usually due to bad information on the boot logical volume, or the log logical volume (/dev/hd8) has been damaged.

To correct the problem with the boot logical volume, enter Maintenance mode (refer to "Accessing a System That Will Not Boot" for information on loading the Maintenance mode onto your system), then run the savebase command. When the savebase command completes, issue the sync; sync command. After this command completes, restart the system in Normal mode.

If this does not correct the problem, reenter Maintenance mode and enter the /usr/sbin/logform /dev/hd8 command. When this command completes, restart the system in Normal mode.

If you are not familiar with this mode or are unable to correct the problem, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 557

Explanation The root file system could not be mounted.
System Action The system halts.
User Action Go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference to determine if there is a problem with the device where the files reside.

If these procedures do not find a problem with a device, the problem is usually due to bad information on the boot logical volume, or the log logical volume (/dev/hd8) has been damaged.

To correct the problem with the boot logical volume, enter Maintenance mode (refer to "Accessing a System That Will Not Boot" for information on loading the Maintenance mode onto your system), then run the savebase command. When the savebase command completes, issue the sync; sync command. After this command completes, restart the system in Normal mode.

If this does not correct the problem, reenter Maintenance mode and enter the /usr/sbin/logform /dev/hd8 command. When this command completes, restart the system in Normal mode.

If you are not familiar with this mode or are unable to correct the problem, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 558

Explanation Not enough memory is available to continue system restart.
System Action The system halts.
User Action Go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference to determine if there is a problem. If these procedures find a problem, report the problem to your hardware service organization. Otherwise, report the problem to your software service organization.

Display Value 559

Explanation Less than 2MB of good memory are left for loading the AIX kernel.
System Action The system halts.
User Action Run hardware diagnostics (from diskettes if available).

Display Value 560

Explanation An unsupported monitor is attached to the display adapter.

Display Value 561

Explanation Progress indicator. The TMSSA device is being identified or configured.
System Action The configuration method for the TMSSA device is being run. If an irrecoverable error occurs, the system halts.
User Action If the system halts with this value, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference to determine if there is a problem. If these procedures find a problem, report the problem to your hardware service organization. Otherwise, report the problem to your software service organization.

Display Value 565

Explanation Progress indicator. Configuring the MWAVE subsystem.

Display Value 566

Explanation Progress indicator. Configuring Namkan twinax commo card (5250 emulation)

Display Value 567

Explanation Progress indicator. Configuring High-Performance Parallel Interface (HIPPI) device driver (fpdev).

Display Value 568

Explanation Configuring High-Performance Parallel Interface (HIPPI) device driver (fphip).

Display Value 569

Explanation Progress indicator. FCS SCSI protocol device is being configured.

Display Value 570

Explanation Progress indicator. A SCSI protocol device is being configured.
System Action The configuration method for the SCSI protocol device driver is being run. If an irrecoverable error occurs, the system halts.
User Action If the system halts with this value, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference . If these procedures find a problem, report the problem to your hardware service organization. Otherwise, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 571

Explanation HIPPI common functions driver is being configured.
System Action The configuration method for a HIPPI common functions driver is being run. If an irrecoverable error occurs, the system halts.
User Action Go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference to determine if there is a problem. If these procedures find a problem, report the problem to your hardware service organization. Otherwise, report the problem to your software service organization.

Display Value 572

Explanation HIPPI IPI-3 master-mode driver is being configured.
System Action The configuration method for a HIPPI IPI-3 master-mode driver is being run. If an irrecoverable error occurs, the system halts.
User Action Go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference to determine if there is a problem. If these procedures find a problem, report the problem to your hardware service organization. Otherwise, report the problem to your software service organization.

Display Value 573

Explanation HIPPI IPI-3 slave-mode driver is being configured.
System Action The configuration method for a HIPPI IPI-3 slave-mode driver is being run. If an irrecoverable error occurs, the system halts.
User Action Go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference to determine if there is a problem. If these procedures find a problem, report the problem to your hardware service organization. Otherwise, report the problem to your software service organization.

Display Value 574

Explanation HIPPI IPI-3 user-level interface driver is being configured.
System Action The configuration method for a HIPPI IPI-3 user-level interface driver is being run. If an irrecoverable error occurs, the system halts.
User Action Go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference to determine if there is a problem. If these procedures find a problem, report the problem to your hardware service organization. Otherwise, report the problem to your software service organization.

Display Value 575

Explanation A 9570 disk-array driver is being configured.
System Action The configuration method for a 9570 disk-array driver is being run. If an irrecoverable error occurs, the system halts.
User Action Go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference to determine if there is a problem. If these procedures find a problem, report the problem to your hardware service organization. Otherwise, report the problem to your software service organization.

Display Value 576

Explanation Generic async device driver is being configured.
System Action The configuration method for a generic async device driver is being run. If an irrecoverable error occurs, the system halts.
User Action Go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference to determine if there is a problem. If these procedures find a problem, report the problem to your hardware service organization. Otherwise, report the problem to your software service organization.

Display Value 577

Explanation Generic SCSI device driver is being configured.
System Action The configuration method for a generic SCSI device driver is being run. If an irrecoverable error occurs, the system halts.
User Action Go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference to determine if there is a problem. If these procedures find a problem, report the problem to your hardware service organization. Otherwise, report the problem to your software service organization.

Display Value 578

Explanation Generic commo device driver is being configured.
System Action The configuration method for a generic commo device driver is being run. If an irrecoverable error occurs, the system halts.
User Action Go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference to determine if there is a problem. If these procedures find a problem, report the problem to your hardware service organization. Otherwise, report the problem to your software service organization.

Display Value 579

Explanation Device driver is being configured for a generic device.
System Action The device driver configuration method for a generic device is being run. If an irrecoverable error occurs, the system halts.
User Action Go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference to determine if there is a problem. If these procedures find a problem, report the problem to your hardware service organization. Otherwise, report the problem to your software service organization.

Display Value 580

Explanation Progress indicator. A HIPPI-LE interface (IP) layer is being configured.
System Action The configuration method for a HIPPI-LE IP layer is being run. If an irrecoverable error occurs, the system halts.
User Action If the system halts with this value, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference . If these procedures find a problem, report the problem to your hardware service organization. Otherwise, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 581

Explanation Progress indicator. TCP/IP is being configured.
System Action The configuration method for TCP/IP is being run. If an irrecoverable error occurs, the system halts.
User Action If the system halts with this value, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference . If these procedures find a problem, report the problem to your hardware service organization. Otherwise, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 582

Explanation Progress indicator. Token-Ring data link control (DLC) is being configured.
System Action The configuration method for the Token-Ring DLC is being run. If an irrecoverable error occurs, the system halts.
User Action If the system halts with this value, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference . If these procedures find a problem, report the problem to your hardware service organization. Otherwise, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 583

Explanation Progress indicator. Ethernet data link control (DLC) is being configured.
System Action The configuration method for Ethernet DLC is being run. If an irrecoverable error occurs, the system halts.
User Action If the system halts with this value, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference . If these procedures find a problem, report the problem to your hardware service organization. Otherwise, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 584

Explanation Progress indicator. IEEE Ethernet (802.3) data link control (DLC) is being configured.
System Action The configuration method for IEEE Ethernet DLC is being run. If an irrecoverable error occurs, the system halts.
User Action If the system halts with this value, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference . If these procedures find a problem, report the problem to your hardware service organization. Otherwise, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 585

Explanation Progress indicator. SDLC (MPQP) data link control (DLC) is being configured.
System Action The configuration method for MPQP DLC is being run. If an irrecoverable error occurs, the system halts.
User Action If the system halts with this value, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference . If these procedures find a problem, report the problem to your hardware service organization. Otherwise, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 586

Explanation Progress indicator. QLLC (X.25) data link control (DLC) is being configured.
System Action The configuration method for X.25 DLC is being run. If an irrecoverable error occurs, the system halts.
User Action If the system halts with this value, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference . If these procedures find a problem, report the problem to your hardware service organization. Otherwise, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 587

Explanation Progress indicator. NETBIOS is being configured.
System Action The configuration method for NETBIOS is being run. If an irrecoverable error occurs, the system halts.
User Action If the system halts with this value, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference . If these procedures find a problem, report the problem to your hardware service organization. Otherwise, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 588

Explanation Progress indicator. Bisync read-write (BSCRW) is being configured.
System Action The configuration method for BSCRW is being run. If an irrecoverable error occurs, the system halts.
User Action If the system halts with this value, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference . If these procedures find a problem, report the problem to your hardware service organization. Otherwise, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 589

Explanation SCSI target mode device is being configured.
System Action The configuration method for the SCSI target mode is being run. If an irrecoverable error occurs, the system halts.
User Action If the system halts with this value, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference . If these procedures find a problem, report the problem to your hardware service organization. Otherwise, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 590

Explanation Progress indicator. Diskless remote paging device is being configured.
System Action The configuration method for the diskless remote paging device is being run. If an irrecoverable error occurs, the system halts.
User Action If the system halts with this value, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference . If these procedures find a problem, report the problem to your hardware service organization. Otherwise, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 591

Explanation Progress indicator. Logical Volume Manager device driver is being configured.
System Action The configuration method for LVM is being run. If an irrecoverable error occurs, the system halts.
User Action If the system halts with this value, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference . If these procedures find a problem, report the problem to your hardware service organization. Otherwise, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 592

Explanation Progress indicator. An HFT device driver is being configured.

Display Value 593

Explanation Progress indicator. SNA device driver is being configured.
System Action The configuration method for SNA is being run. If an irrecoverable error occurs, the system halts.
User Action If the system halts with this value, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference . If these procedures find a problem, report the problem to your hardware service organization. Otherwise, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 594

Explanation Asynchronous I/O is being defined or configured.
System Action The configuration method for an asynchronous I/O is being run. If an irrecoverable error occurs, the system halts.
User Action If the system halts with this value, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference . If these procedures find a problem, report the problem to your hardware service organization. Otherwise, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 595

Explanation X.31 pseudo device is being configured.
System Action The configuration method for an asynchronous I/O is being run. If an irrecoverable error occurs, the system halts.
User Action If the system halts with this value, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference . If these procedures find a problem, report the problem to your hardware service organization. Otherwise, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 596

Explanation SNA DLC/LAPE pseudo device is being configured.
System Action The configuration method for the SNA DLC/LAPE is being run. If an irrecoverable error occurs, the system halts.
User Action If the system halts with this value, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference . If these procedures find a problem, report the problem to your hardware service organization. Otherwise, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 597

Explanation Outboard communication server (OCS) is being configured.
System Action The configuration method for an OCS is being run. If an irrecoverable error occurs, the system halts.
User Action If the system halts with this value, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference . If these procedures find a problem, report the problem to your hardware service organization. Otherwise, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 598

Explanation OCS hosts is being configured during system reboot.
System Action The configuration method for OCS hosts is being run. If an irrecoverable error occurs, the system halts.
User Action If the system halts with this value, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference . If these procedures find a problem, report the problem to your hardware service organization. Otherwise, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 599

Explanation Progress indicator. FDDI data link control (DLC) is being configured.
System Action The configuration method for the FDDI DLC is being run. If an irrecoverable error occurs, the system halts.
User Action If the system halts with this value, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference . If these procedures find a problem, report the problem to your hardware service organization. Otherwise, report the problem to your software service organization, and then stop. You have completed these procedures.

Display Value 5c0

Explanation Progress indicator. Streams-based hardware drive being configured.
System Action If an irrecoverable error occurs, the system halts.
User Action If the system halts, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference.

If there is a hardware failure, report it to your hardware service organization. If not, report the failure to your software service organization, and then stop. You have completed these procedures.

Display Value 5c1

Explanation Progress indicator. Streams-based X.25 protocol stack being configured.
System Action If an irrecoverable error occurs, the system halts.
User Action If the system halts, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference.

If there is a hardware failure, report it to your hardware service organization. If not, report the failure to your software service organization, and then stop. You have completed these procedures.

Display Value 5c2

Explanation Progress indicator. Streams-based X.25 COMIO emulator driver being configured.
System Action If an irrecoverable error occurs, the system halts.
User Action If the system halts, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference.

If there is a hardware failure, report it to your hardware service organization. If not, report the failure to your software service organization, and then stop. You have completed these procedures.

Display Value 5c3

Explanation Progress indicator. Streams-based X.25 TCP/IP interface driver being configured.
System Action If an irrecoverable error occurs, the system halts.
User Action If the system halts, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference.

If there is a hardware failure, report it to your hardware service organization. If not, report the failure to your software service organization, and then stop. You have completed these procedures.

Display Value 5c4

Explanation Progress indicator. FCS adapter device driver being configured.
System Action If an irrecoverable error occurs, the system halts.
User Action If the system halts, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference.

If there is a hardware failure, report it to your hardware service organization. If not, report the failure to your software service organization, and then stop. You have completed these procedures.

Display Value 5c5

Explanation Progress indicator. SCB network device driver for FCS is being configured.
System Action If an irrecoverable error occurs, the system halts.
User Action If the system halts, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference.

If there is a hardware failure, report it to your hardware service organization. If not, report the failure to your software service organization, and then stop. You have completed these procedures.

Display Value 5c6

Explanation Progress indicator. AIX SNA channel being configured.
System Action If an irrecoverable error occurs, the system halts.
User Action If the system halts, go to "Hardware Diagnostics" in in AIX Problem Solving Guide and Reference.

If there is a hardware failure, report it to your hardware service organization. If not, report the failure to your software service organization, and then stop. You have completed these procedures.

[ Previous | Next | Contents | Glossary | Home | Search ]